Here is the complete guide about Anti-Roll-Bar Bushes. Here you can get How to replace anti-roll-bar bushes.
The anti-roll bar (also called the sway bar or the stabilizer bar) is a part of your vehicle’s suspension system that connects the left and right wheel together to help limit body roll and keep wheels in contact with the ground. Anti-roll bar bushes are found between the joints of this system.
The forces imposed on the anti-roll bar subject it to constant twisting and flexing, which in turn put its various rubber mounting bushes under great load. The bushes gradually wear and lose their effectiveness. Over a period of years the rubber hardens and tends to crack.
If oil is allowed to contaminate the bushes, it softens them rapidly and that they may even disintegrate. Anti-roll bars are sometimes fitted only to the front suspension , but many cars even have them fitted to the rear suspension.
Check all the anti-roll-bar bushes at the intervals recommended in the service schedule for the car, or at intervals of 6,000 miles (10,000km) or six months. If any bush is damaged or worn, replace it – and therefore the corresponding bush on the other side of the car. If one is broken, the other is probably in poor condition too. Any bushes that are split length ways can usually be renewed without removing the bar completely. If the bush isn’t split, the bar must be removed. Drive the front or rear of the car up on ramps or over an inspection pit.
Checking for wear
If you use ramps, make sure the handbrake is applied firmly which the wheels still on the bottom are chocked. The weight of the car on the suspension reduces the load on the anti-roll bar mounts and makes them easier to unbolt and refit.
Anti-Roll-Bar Bushes
The anti-roll bar (also called the sway bar or the stabilizer bar) is a part of your vehicle’s suspension system that connects the left and right wheel together to help limit body roll and keep wheels in contact with the ground. Anti-roll bar bushes are found between the joints of this system. As its name implies, an anti-roll bar reduces your vehicle’s roll when cornering. The bushings are made of rubber, nylon or polyurethane and wear out over time. If your anti-roll bar bushings are worn, you might hear squeaks or rattles coming from under your vehicle.
Another way to replace bushes
However, you’ll find the road wheels prevent you from reaching some of the bushes, therefore the wheels should be removed. therein case, raise the car by a different method – which may even be used if you are doing not have ramps or a pit. Loosen the wheel nuts at the top you’re working on, jack up the car and support it on axle stands under the chassis members. Remove the road wheels.
Jack up each lower suspension arm and support it to reduce the load on the anti-roll-bar mounts. Unscrew the nuts or bolts which hold the U-clamps and their bushes to the floor pan . Make a careful note of the number and position of the components as you remove them. Pull the anti-roll bar down, achieve the bushes if they’re the split type. If they’re not split, free the top of the bar from its mounting on the suspension arm and pull the bush along the bar and off.
It may be easier to cut the old bushes free, or they’ll be lubricated with soap solution to ease them along the anti-roll bar. If you have to exchange the end bushes on the anti-roll bar, you’ll have to remove the complete bar.
Fitting eye bushes
New eye bushes can be drawn into place with a socket, a long bolt and a large washer. The socket should be of slightly larger diameter than the bush. Put the socket at one side of the eye into which you are fitting it, and the bush at the other side. Pass the long bolt through the socket, the eye and the bush. Fit the washer and the nut and tighten the whole assembly. This draws the new bush into place.
The bushes on the short vertical links to the anti-roll bar can be dealt with in the same way. Sometimes they are eye fittings, others fit around the shaft of the link itself. Align the new bushes with the marks worn on the bar by the old ones. Refit the various shims, washers, clamps and bolts, and push the bar up towards the floor pan, or cross member. Screw in the mounting bolts. Make sure that they are fully tightened.
In some cases, these nuts or bolts should be tightened with a torque wrench to a specific torque setting. The figure will be given in a service manual for the car – otherwise, ask your local dealer. When you have replaced the bushes, remove the wheel chocks and lower the car to the ground.
Removing vertical links
If the anti-roll bar is connected to the suspension by short vertical links, you’ll be able to replace their bushes by removing the links without disturbing the most bar. Inspect them carefully – you ought to be able to judge whether removal is possible. If in doubt, consult the car service manual. Whatever the layout of the links, jack the end of the car and support it on axle stands.
In some cases the ends of the bar are threaded, and pass through a bush within the arm. A lock nut is fitted to the top of the bar to hold it in place. Remove the nut and pull the bar out. There may be eye fittings at each end of the bar, which is held to a bracket on the suspension arm or axle by a pivot bolt. Unscrew and remove the bolt. Make a careful note of all washers, shims and spacers that make up the mounting; they must be replaced in just the same order as they came off. Always renew any lock nuts.
Rear-suspension types
Anti-roll-bar mounts vary from car to car. Some bars form a link across the rear axle and attach to the suspension arm on each side. Others may link the leaf springs , passing over the axle tube with firm mountings on chassis members or floor pan. On torsion-bar suspension, the anti-roll bar runs from one arm to the other, the central part again being clamped to the ground pan.
Fitting end pins or eye bolts
Some anti-roll bars have vertical links at the ends connected to the suspension. The links may have end-pin fittings, or eye-bolt fittings. The pin fitting in particular may have a distance piece within the form of a tube between two washers or end plates. The distance pieces take the load, while the rubber bush takes the shocks – do not forget to replace the distance piece when you fit new bushes.
With the car raised on axle stands, use a jack under the suspension arm to take the load off the anti-roll bar, so that it does not fly apart violently when a mounting clamp is released. The jack also can be used to raise or lower the arm to help in aligning the vertical link with a mounting hole. Use a vice to press new bushes into a rod with an eye mounting by squeezing the bush into the eye.
Removing the bar
Look underneath the car to find the U-clamps which hold the anti-roll bar to the floor pan or suspension cross member. Make a careful note of any washers, spacers and other parts of the mounting. make sure that they’re replaced in exactly the same way. Check the position of the bushes and, in particular, the position of any marks or splits within the rubber bushes in reference to the bar, in order that you’ll fit the new bushes in just an equivalent way.
Use a socket spanner to slacken the U-clamp mounting bolts and nuts. If you are doing not have a socket, use a ring spanner. Use an open-ended spanner only as a last resort, for these nuts and bolts tend to be misshapen due to corrosion, and wish the best grip possible. Remove the nuts, bolts, washer clamps and spacers from each mount, at each end and towards the center of the bar. Collect all the pieces and keep them in the correct order.
Pull the anti-roll bar downwards from the floor pan or cross member until there’s sufficient clearance to take it out. Take all the old rubber bushes off. Lever all off with a screwdriver or similar tool if they do not slip off easily. Wipe the bar clean. Coat it with soap solution to lubricate the path for the tight new rubber bushes. Press each new rubber bush over the anti-roll bar. make sure that the split within the rubber bush faces within the same direction as the old one, if applicable, which the new bushes fit over the wear marks left by the old bushes.
Removing the bar from a rear-spring mounting arm
On some cars the rear anti-roll bar is secured underneath the independent coil-spring mounting arm. Place a jack under the arm to take the load off the suspension, and unscrew the pair of nuts securing the through-bolts. Adjust the jack until there is no load on the anti-roll bar, at which point the bolts should push out freely. The bar will then pull down.
