Here you can get How to properly Installing car window blinds, Types of car window blind and Feature steps of blinds.
As well as improving the look of your car, rear windscreen blinds have variety of practical benefits. First they create your car safer because they hide any valuables on the rear shelf (including radio-cassette speakers) from an off-the-cuff car thief passing by.
They also help to keep your car interior cool on a hot summer’s day by blocking the daylight pouring through the rear screen, and that they reduce dazzle in your rear view mirror, whether it’s from the headlights of the car behind you or from bright sunlight.
You have a choice of two types of blind – roll-up and louvred, the louvred types being basically similar to a household venetian blind. Roll-up blinds are often easier to suit , but they are doing have one disadvantage – they need to be either up or down. With louvred blinds, however, you’ll vary the quantity of light coming through the rear screen by tilting the slats.
Always remember, however, that you simply should never drive with the slats angled in such how that they impair your rear-view vision. A further advantage of louvred blinds is that some of them are electrically operated by a dashboard-mounted control, which allows you to regulate the slats from the driver’s seat. Some Models even open and close the blinds automatically once you switch the ignition on and off. this text covers fitting louvred blinds only.
Louvred blinds fit on the inside of the rear screen and are available during a range of colors in order that you’ll match or contrast them with the color of your car interior. They will be fitted to most models, including hatchbacks. As well because the electrically operated louvred blinds, you’ll also buy manually operated ones. The procedure for fitting the blind itself is that the same, whether it’s an electrically or manually operated one.
1. Marking out
Use a tape to seek out the centre of the rear screen at the top and bottom. Mark these positions on the surface with a felt-tipped pen . offer to the centre line the template provided within the kit. Mark the fitting positions for the mounting brackets on all sides of the screen, top and bottom.
2. Ladder length
Place the template on the within of the screen (this time on its edge). Trim rock bottom off the template until it clears the parcel shelf. this provides you the required length of the support ladders. offer the template to the ladders and their aluminium extrusions and mark the template length on them.
3. Cutting ladders
Use alittle hacksaw carefully to chop the ladders and their aluminium extrusions at the marked positions. When cutting the extrusions confirm the dimple formed in them remains on the measured section. Remove the top slat clip from the cut-off section and transfer it to the ladder top clip position.
4. Fit extrusions
Fit the 2 aluminium extrusions to the ladder inner rails —the ones next to the window. confirm the dimples formed within the end of every extrusion are at the top of the ladder rail. Push each extrusion over the inner rail until the dimple grips the rail and holds it securely.
5. Top window brackets
Clean the window and make sure it is dry. Fit the upper ladder support brackets by removing the protective backing paper from the self-adhesive pad. Slide the bracket extension lugs under the window seal, at the same time as pressing the bracket base on to the window glass. Make sure you achieve a firm contact.
6. Assemble blind
Lay the 2 ladder assemblies on a flat surface with the extrusions at rock bottom . (If fitting an electrical blind, the motor should get on the left-hand side.) Pass the lean rod through the lower slat clips on each ladder and therefore the motor gearbox (if applicable). Fit two blind slats to the top clips of the ladder.
7. Lower brackets
offer the assembly, fixing the top slat clips to the upper window brackets. Fit the serrated pins to the ladder drive arms, pertaining to the instructions for the left-hand and right-hand fitting positions. Move the ladders to the open position and secure the adhesive bracket pads to the glass.
8. Fitting slats
Remove the assembly from the window. Fit a pair of slats to every clip by passing them through the ladders. Refit the assembly then pull the slats bent the left and right to match the form of your window. Fit the four black stickers to the surface of the window to hide the pads of the mounting brackets.
9. Electric blind wiring
Mount the control unit to the dash. Disconnect the battery. Run the extension wire from the control unit under the carpets to the rear blind motor. Run the red wire to a permanent live feed and therefore the yellow wire to an ignition-controlled live feed. Run the black wire to earth. Reconnect the battery and test.